3M VPS Tray Adhesive Refill 7307 – 17 ml
An air-drying tray adhesive designed to support retention of 3M vinyl polysiloxane impression materials in compatible dental impression trays.
3M VPS Tray Adhesive Refill 7307 is an air-drying dental tray adhesive designed to support retention between 3M vinyl polysiloxane impression material and a properly prepared impression tray. It is intended exclusively for VPS impression procedures and should not be used with alginate or polyether impression materials.
The adhesive is suitable for compatible impression trays made from metal, polypropylene, or methacrylate when used with 3M VPS impression materials. The official 3M product information identifies the product as catalogue number 7307, product ID UU009806009, supplied in a 17 ml bottle.
A thin, uniform coating is applied to clean and dry tray surfaces that will contact the impression material. After complete air drying, the tray can be loaded with the selected VPS material. Correct application supports retention of the set impression material within the tray during seating, setting, and removal.
Tray adhesive supports material retention but does not independently guarantee an accurate or distortion-free impression. Impression quality also depends on tray selection, rigidity, preparation, adhesive drying, material handling, intraoral stability, setting time, and removal technique.
Indications
- Retention of 3M VPS impression material within compatible impression trays
- VPS impressions using metal trays
- VPS impressions using polypropylene trays
- VPS impressions using methacrylate trays
- Professional dental impression procedures in which a compatible 3M VPS material is indicated
- Tray adhesive specifically intended for VPS impression materials
- Designed for use with 3M vinyl polysiloxane impression materials
- Compatible with metal, polypropylene, and methacrylate impression trays
- Air-drying application
- Thin adhesive-film technique
- Supports retention of impression material within the tray
- Liquid bottle presentation
- Red, viscous formulation
- Solvent-based adhesive system
- Catalogue number 7307
- Supplied in a 17 ml bottle
- Intended for professional dental use
Pack Contents
- 1 × 17 ml 3M VPS Tray Adhesive bottle
Product Identification
| Attribute | Details |
|---|---|
| Catalogue Number | 7307 |
| 3M Product ID | UU009806009 |
| UPC | 04054596648609 |
The official 3M listing confirms one 17 ml bottle per refill pack.
| Attribute | Specification |
|---|---|
| Brand | 3M |
| Product Name | VPS Tray Adhesive |
| Product Type | Dental Impression Tray Adhesive |
| Intended Impression Material | Vinyl Polysiloxane / VPS |
| Drying Method | Air Dry |
| Physical Form | Viscous Liquid |
| Colour | Red |
| Compatible Tray Materials | Metal, Polypropylene and Methacrylate |
| Recommended Material System | 3M VPS Impression Materials |
| Presentation | Bottle |
| Net Quantity | 17 ml |
| Catalogue Number | 7307 |
| Intended User | Qualified Dental Professional |
The formulation is highly flammable and has an SDS-reported flash point of −3.9°C. Refer to the current 3M Safety Data Sheet for complete physical, chemical, handling, and transport information.
- Select an appropriately sized and rigid impression tray compatible with the planned VPS impression material.
- Trial-fit the tray to confirm adequate extension and patient fit.
- Clean the tray thoroughly and remove any contamination or residue.
- Dry the tray completely before applying the adhesive.
- Using the bottle brush, apply a thin and uniform layer to all tray surfaces that will contact the VPS impression material.
- Avoid pooling or applying an unnecessarily thick coating — excess material does not improve retention.
- Allow the adhesive to air-dry completely for the period stated in the current 3M instructions supplied with the product. The referenced application information indicates a minimum drying time of 5 minutes, with approximately 15 minutes preferred where the workflow permits.
- Do not touch or contaminate the dried adhesive film.
- Load the tray with the selected 3M VPS impression material according to its instructions.
- Seat, stabilise, and remove the impression according to the selected impression technique and the material's setting time.
- Close the adhesive bottle immediately after use.
Follow the current 3M instructions supplied with the product where they differ from the general procedure above. For professional dental use only.
Clinical Considerations
- Use only with vinyl polysiloxane impression materials.
- Do not use as a tray adhesive for alginate.
- Do not use as a tray adhesive for polyether impression materials.
- The product is not an enamel, dentin, or restorative bonding agent.
- Do not apply the adhesive directly inside the patient's mouth.
- Use with 3M VPS impression materials as specified by 3M.
- Compatibility with VPS materials from other manufacturers should not be assumed.
- Apply only to clean, dry, and compatible tray surfaces.
- Use a thin, uniform coating rather than a thick or pooled layer.
- Allow the solvent to evaporate and the adhesive to dry completely before tray loading.
- Avoid touching the dried adhesive film.
- Final impression accuracy depends on the complete clinical technique, not the tray adhesive alone.
Safety Information
The SDS classifies the product as a Category 2 flammable liquid and states that its vapour may cause drowsiness or dizziness.
- Highly flammable liquid and vapour
- Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources
- No smoking near the product
- Use only in a well-ventilated area
- Avoid breathing vapour, mist, or spray
- Avoid prolonged or repeated skin contact
- Prevent contact with the eyes
- Wear suitable eye protection where exposure is possible
- Keep the container tightly closed when not in use
- Wash thoroughly after handling
- For professional dental use only
Storage and Handling
- Store in a cool, well-ventilated place.
- Keep the bottle tightly closed.
- Store away from heat and ignition sources.
- Store away from acids and oxidising agents.
- Protect the bottle from physical damage.
- Do not use after the expiry date printed on the pack.
- Dispose of unused material and empty packaging according to applicable regulations.
| Brand | 3M ESPE |
|---|
To facilitate accurate invoicing and maintain tax compliance, we kindly request that you provide your GST number.
Why is this necessary?
The GST number enables us to issue precise invoices for your order, ensuring adherence to tax regulations.
Please fill out your Registration Number / ID
To proceed with your order, kindly enter your Medical Registration number or Medical ID.
Change Pincode
- Buy 2 for ₹1,480.00 each and save 1%
- Buy 5 for ₹1,465.00 each and save 2%
Available Offers
| Offer | Add on Savings |
|---|---|
| Buy 2 for ₹ 1,480.00 each | 1% |
| Buy 5 for ₹ 1,465.00 each | 2.01% |
Want to buy even more quantity?
Get Bulk Quote Now
100% Genuine Products
Easy Returns
On Time Delivery
Secure Checkout
